ZRsuns 100W CO2 laser power source for 1390 co2 laser engraving machine

Precio FOB

Obtener el precio más reciente

109 ~ 119 USD / Piece ( Negotiable )

50 Piece Minimum Order

País:

China

N º de Modelo:

ZR-100W CO2 laser power supply

Precio FOB:

109 ~ 119 USD / Piece ( Negotiable )(Negociable) Obtener el precio más reciente

Lugar de origen:

jinan china

Precio de pedido mínimo:

109 per Piece

Cantidad de pedido mínimo:

50 Piece

Detalle de embalaje:

carton and foam

El tiempo de entrega:

3-4 working days after payment received

Capacidad de suministro:

4000 Piece per Month

Tipo de pago:

T/T, D/P, Western Union, Money Gram

Grupo de productos :

Contactar ahora

Jinan Ruby Laser Technology Co., Ltd

China

Miembro Básico

Persona de contacto william

Jinan, Shandong

Contactar ahora

Especificaciones del producto

two cooling fans:220/110V AC

Descripción del producto

ZR***0W CO2 POWER SOURCES
Feature
1. The **0w laser power supply unit can match with EFR,SPT,Yongli, Weiju and other brands' ******5cm sealed glass type CO2 laser lamp. The external LCD laser power supply unit selects zero-current half-bridge soft-switch circuit to make sure the air cooling laser power supply unit has high efficiency and fast response speed.
2.The air cooling laser power supply unit's control interface is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.
3.This air cooling laser power supply unit has RED TEST to easily figure out CO2 power supplies or CO2 laser tube's failure. It is very easy and simple to remove trouble.
4.Each external LCD laser power supply unit before selling will go through the aging check:
(1) sustain *0 hours at temperature *0 Degrees Celsius under full-load condition;
(2) **0 times on/off check for 7 seconds.
5. Input analog signal(0~5V) or PWM is selected to control the output laser power on this **0w laser power supply unit.
6. The **0w laser power supply unit has H/L/P/G/IN/5V control signal interfaceï¼ŒThe upper cover and bottom shell are aluminum Casing is made of galvanized sheet.
7.The **0w laser power supply unit is well grounded, which can ensure the safety of operators. At the same time, the air cooling laser power supply unit also has an open circuit protection function, which allows the external LCD laser power supply unit to work for a short time in the open circuit state.
8.This**0w laser power supply unit is equipped with two cooling fans. Better heat dissipation can protect the internal electronic components of this power supply.
9.This laser engraving power supply unit can use an external LCD module. It can display common fault codes, output current and working status. It is helpful for operators to understand the working state of **0w laser power supply unit and solve problems quickly. In addition, the output current can also be changed by the rotating potentiometer of the LCD module.
Specification

lnput	Input voltage			AC*0V±0% (AC**0V specified while order)
	AC frequency			7~*0HZ
	Maximum power			**0W
	Maximum current			3.5A
Output	Maximum output voltage			*5KV
	Maximum output current			*3mA (depending on the laser tubes of different manufacturers)
Efficiency				More than *0% (Full load)
Response speed				Not more than 1ms
Control lnterace				TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)
Insulation		lnput-output		AC **0V 1 minutes not more than 0mA
		lnput-shell		AC **0V 1 minutes not more than0mA
		Output-shell		Connection
Open Circuit Protection				Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)
Environmental Requested			Working temperature	*0â„ƒ~0â„ƒ
			Storage of temperature	*0â„ƒ~5â„ƒ
			Relative Humidity	Maximum *5%RH (non-condensing)
			Altitude	0,0 feet of work 0,0 feet of storage,dose not work
Cooling methods				Forced air cooling (fan cooling)
Dimensions (LxWxH)				5mmx5mmx**2mm

País:	China
N º de Modelo:	ZR-100W CO2 laser power supply
Precio FOB:	109 ~ 119 / Piece ( Negotiable ) (Negociable) Obtener el precio más reciente
Lugar de origen:	jinan china
Precio de pedido mínimo:	109 per Piece
Cantidad de pedido mínimo:	50 Piece
Detalle de embalaje:	carton and foam
El tiempo de entrega:	3-4 working days after payment received
Capacidad de suministro:	4000 Piece per Month
Tipo de pago:	T/T, D/P, Western Union, Money Gram
Grupo de productos :	-