Descripción del producto
MAIN STRUCTURE AND THE
FEATURES
1.The machine is
composed by the box-seat, universal bearings, fly lose, chassis,
belt lose, blanking network support, knife-axis, the activities
of the blade, a fixed blade, feed doors, and the car containing
material,Spindle and blades rotate around
the V-belt controlled by the motor. The material is crushed by
the free blades on the spindle and the fixed blades on the
box.
2. The cutter is
imported from Japan, which can be used for a long time. The
machine can be separated into several independence parts. Then,
it is easy for you to check and clean. And also it has a
double-deck structure, equipping with the sound insulation
materialwhich can make the noise lower.
INSTALLATIONINSTRUCTIONS
1. The machine adopts
the three-phase power, and plugs into the appropriate voltage
according to the show of data plate, then, it connects the ground
wire.
2. After fixing the
machine into a appropriate position, you must fix and lock the a
real wheel to avoid making some noise when you move the
machine.
3. This machine is
equipped with the safe micro switch, which is regarded as a
security protector to keep off the wrong operation while
overhauling. When the machine is installed, users should device
independent switch in order to cut off the power and avoid the
operating accident etc.
4. The machine is
equipped with the water-cooling system, two water pipes are in
order to enter water, surface, connect the running water pipe
according to the mark.
BEFORE USING YOUR
GRANULATORS
1. The preparation
before using: According to the granularity of need, adjust the
interval of razor blade; use the screen mesh of different
aperture first.
A. Open the charging
door and blanking network support, check whether there is odds
and ends or metal material in the pulverize room.
B. Check the rotator
razor blade and revitalize the interval of the fixed cutting
edge, the razor blade fastens the bolt to lock, whether the
spring washer plays a role in compressing tightly.
C. Rotate flywheel
with hand, check, it operates to be normal.
D. Check it is firm
that the feed inlet glue board is connected with charging door,
compress tightly the nut to lock.
E. The bearing on the
main shaft should pour into enough lubricating oil to
chew.
2. The
operation
A. operator of the
machine must be familiar with the knot machine of the machine and
operation principle.
B. check to it turns
to be correct electrical machinery (chew and point out according
to belt arrow covered to protect)
C. checks whether the
elasticity intensity of the V belt is
appropriate.
D. starts the machine
for five minutes air transport rotates, it is normal that checks
and operates.
E. machine work,
operator should take, protect glasses and ear put on, should also
feed inlet both sides feed in raw material in machine; make sure
not to be facing the reinforced mouth.
NOTICE
1 Of safety in
operation of the pulverizer. It feeds to be should appropriate,
avoid, put a large number of into or too big plastic lead to the
fact card hinder now as take place Carlos hinder and should shut
down immediately, it should be even to throw the material,
prevent machine burden from being overweight and result in
damaging.
2. Find the cutting
edge should repair or change the razor blade in time while having
blunt mouths or damaging.
3. Pay attention to
the motor bearing situation of generating heat at any time,
temperature can't exceed *0 degrees C.
4. Forbade throwing
the material in 6 minutes before shutting down, the ones that
treated in the pulverizer room stored the material and can shut
down after totally crushing.
5. It is difficult
for plastic not to enter pulverizer at the room, make sure not,
bulldoze with hand, with accident, should shut down, clear up or
in charge of, dredge dish with plastic.
6. Forbid having metal part and
hard supplies in the broken thing, so as not to cause the razor
blade and mechanical damage.
OPERATING YOUR
GRANULATORS
1. While adjusting
the razor blade, based on fixed razor blade, adjust the razor
blade of the activity, its relative interval is 0.**0.8mm, the
following broken plastic all kinds of, razor blade interval test
form:
|
Seq.
|
Plastic Size
|
Cutter Clearance
|
Cutter Size
|
|
1
|
plastic thin
slice
|
0.3mm
|
Flat/Claw Cutter
|
|
2
|
Soft Plastic
|
0.**0.5mm
|
Flat Cutter
|
|
3
|
Hard Plastic
|
0.**0.6mm
Screen
stencil aperture<=Ø**8mm
0.**0.6mm
Screen
stencil aperture<=Ø ***0mm
|
Claw Cutter
|
| País: |
China |
| N º de Modelo: |
NPM-V5000-SC
|
| Precio FOB: |
1000 ~ 20000 / Set ( Negotiable ) (Negociable)
Obtener el precio más reciente
|
| Lugar de origen: |
China |
| Precio de pedido mínimo: |
1000 per Set |
| Cantidad de pedido mínimo: |
1 Set |
| Detalle de embalaje: |
Standard wooden case |
| El tiempo de entrega: |
5 days after receiving deposit |
| Capacidad de suministro: |
1000 Set per Month |
| Tipo de pago: |
T/T, Western Union, Other |
| Grupo de productos : |
Plastic Crusher
|
