¿Aún no es miembro de TradeKey.com? Regístrese para conectarse con 9 millones de importadores y exportadores a nivel mundial. registro |
BOOK A CALL
Book Call On Your Favorite Time
Code
🗘

By Signing Up. I agree to TradeKey.com Terms of Use, Privacy Policy, IPR and receive emails related to our services

Contact Us
Programming-card for ESC (Advance plus prog-card)

Programming-card for ESC (Advance plus prog-card)

|

Minimum Order

Place of Origin:

-

Price for Minimum Order:

-

Minimum Order Quantity:

-

Packaging Detail:

-

Delivery Time:

-

Supplying Ability:

-

Payment Type:

-

Contactar ahora
Miembro Básico

Persona de contacto Ms. shirley

5th Floor, Building 10, No.300 Pushan RD, Shanghai, Zhabei District

Contactar ahora

Description

PULSO ESC (Electronic speed controller) Prog-Card was developed for you to make PULSO Advance plus ESC setting easier and extend the possiblity of ESC setting. OperationFor ESC with Advance plus Prog-Card 1. Connection (Connect the motor & ESC / Connect the receiver & ESC) 2. Using of Advance plus Prog-Card and Start-Up 1) Put the six black jumper connector to the required positions. 2) Plug JR connector (part of ESC) to the position controller on Prog-Card. 3) Connect the motor to the ESC. 4) Connect the power pack to the ESC. l For ESC with BEC , 1 beep will be heard, which means your setting has been saved. l For ESC without BEC, 1 beep will be heard after, connecting the 4.8V (receiver pack) to the position external power for OPTO. 5) Disconnect the power pack. 6) Disconnect the Advance plus Prog-Card. 7) Plug JR connector (part of ESC) to the receiver-motor control channel. 8) Switch on the transmitter. 9) Put the throttle stick at the lowest position. *0) Connect the power pack to the ESC. (For ESC without BEC, switch on the power to the receiver.) *1) 1single beep (Brake is on) or 2 single beeps (Brake is off) will be heard. (Note: If you do not hear beeps, please disconnect the battery & ESC. Wait for 5 seconds and repeat the connection.) *2) 5 seconds later, 5 single beeps (Timing low mode) or 5 double beeps (Timing high mode) will be heard. *3) Now you can move the throttle stick to begin the flight. V. Option parameters Of the Programming Card: 1. Battery Type: l ACCU Ni-XX (NICD or NIMH) l ACCU Li-XX (Li-Pol or Li-Ion.) 2. Brake Mode: On / Off 3. Cut-Off voltage: High / Low l High0.9V for Ni-CD & Ni-MH; 3.0V for Li-ion/Li-polymer. l Low0.7V for Ni-CD & Ni-MH; 2.7V for Li-ion/Li-polymer. 4. Timing Mode: High / Low l High (hard timing)recommended for outrunner motors. l Low (soft timing)maximum efficiency for normal motors (2, 4, 6 pole motors). mode**- to the cut-off 5. Cut-Off Mode: Hard / Slow down l Hardthe motor is fully off immediately as the voltage drops to the cut-off voltage. l Slow downthe motor turns off slowly by power reduction (when the voltage drops) 6. Throttle Curve: Linear / Logarithm l Linear**-soft throttle curve. When the throttle at the mid-position, RPM=*0% of Max RPM. (Be suitable for F3A, 3D models, etc.) l Logarithm**-sensible throttle curve. When the throttle at the mid-position, RPM=*0% of Max RPM. (Be suitable for Glider models, etc.)

Send a direct inquiry to this supplier

A:

Ms. shirley < Shanghai Danlions International Co., Ltd >

quiero saber: