Descripción del producto

Specifications of the machine
 
PSK ****7
*0
***0x***0
**0x**0
**0x**0x**0x*0
Slotting type L(mm)
**0x*5x**0x*5
Max slotting depth (mm)
**0
Width of slotting(mm)
7
Max board thickness 
*2
Max printing area (mm)
***0x***0
Normal printing thickness (mm)
7.2
*2
 
PSK*****3 And PSK*****7 Main Configuration
 
1.1 Chain type manual feeding for the Feeder unit
 
2. Printing roller
2.1.1 Printing roller diameter is **6 mm (**0 mm including the plate), after the steel plate welding, the surface done hard chromium plating, shaft core parts quenched and tempered treatment, make it have strong resistance to fatigue and toughness; And doing the dynamic balancing correction.
2.1.2 Adopts hanging wheel fixed version, and have the full and half-version hanging groove, suitable for 3 X *0 mm hanging article.
2.1.3 When mounting and dismounting the printing plate, can use the pedal switch electric control the forward and backward moving.
2.2  Bottom Printing Pressing Roller
2.2.1 Outer diameter is **5 mm, Steel shaft surface with hard chrome plating; done the dynamic balancing correction.
2.2.2. Printing press roller clearance, manual adjustment, figures shows on the dials, adjusting range is ***2 mm.
 
2.3Paper feeding roller
2.3.1 Paper Feeding roller is solid steel shaft, *0 mm diameter; with four pieces of paper pressing rings.
2.3.2 Paper feeding shaft head uses the one-way bearing structure, is convenient for the upper roller adjustment.
2.3.3 Paper feeding bottom roller diameter is **5 mm, surface hard chromium plating; done the dynamic balancing correction.
2.3.4 Paper feeding bottom roller clearance, manual adjustment, figures shows on the dial, adjusting range is ***2 mm.
 
2.4Inking rubber roller
2.4.1 Outer diameter of is **6.4 mm, is made of high quality seamless steel shaft; and done the dynamic balancing correction.
2.4.2 Surface covering the wear-resisting rubber, rubber roller peak is the parabola form, via special grinding, ink transfer effect is good.
2.4.3 The gear motor adopted with chain driven on the rubber roller when the host machine stop running
2.4.4 the clearance between with Anilox Roller, manual adjustment, figures showing on the dial, adjusting range is **6 mm.
 
2.5   Anilox roller
2.5.1 Outer diameter is **5 mm, use a metal flower roller, done the dynamic balancing correction.
2.5.2 Has a time delay function, can automatic sequential lifting with the feed system.
2.5.3 The clearance between Anilox roller and the printing roller, manual adjustment, figures showing on the dial, adjusting range is **6 mm.
 
2.6Phase adjustment
 
2.6.1 Phase adjustment mechanism with planetary gear structure, **0 degree precision adjustments.
2.6.2 Phase adjustment adopts electric control, digital display; with memory function, can reset to original printing points after midway brushing the plate.
2.6.3 Transversal movement is manual control, adjusting scrope is ±8mm..
2.6.4 Phase fixed with electromagnetic brake mechanism, when separating the unit or adjust the register, the brake system restrict the machine running and keep plate fixed position.
 
2.7Ink supply system
2.7.1 Adopt pneumatic diaphragm pump circulation supplies, inking stability, convenient operation, and simple maintenance.
2.7.2 Water ink fountain is stainless steel material.
 
3Slotter
3.1Slitter wheel
3.1.1 Top and bottom creasing shaft diameter is *0 mm, made of solid steel, surface ground, again, after the hard chromium plating, moving smoothly.
3.1.2 The top creasing shaft surface covered with the rubber , do not damage the cardboard, the rubber and creasing seat adopts detachable type structure, is convenient to replace.
3.1.3 The bottom creasing clearance, is manual adjustment, figures shows on the dials; adjusting range is ***2 mm.
 
3.2 Slotting knife shaft
3.2.1 Slotting knife shaft diameter is **5 mm, surface grinding process, again, after the hard chromium plating, moving smoothly.
3.2.2 Upper slotting knife material adopt alloy steel, the width is 7mm, ground after heat treatment, the hardness is HRC****3, toughness is better.
3.2.3 Bottom slotting knife material is made of alloy steel, ground after heat treatment; Hardness is HRC****3, toughness is better.
3.2.4 Trimming knife material is the same as slotting knife, upper blade point is V type whole circle, bottom knife is biplate, ground after heat treatment, hardness of HRC****3, the blade point is sharp.
3.2.5 Bottom Slotting knife clearance is manual adjustment, figures shows on the dial; Adjust range is ***2 mm.
 
3.3Phase adjustment
3.3.1 Phase adjustment mechanism with planetary gear structure, **0 precision adjustments.
3.3.2 Phase adjustment adopts electric control, digital display; With memory function, to restore the original after midway adjustment.
3.3.3 Carton height is manual adjustment, four knives is synchronous adjusted
3.3.4 Phase fixed with electromagnetic brake mechanism, when the machine separation or adjust the phase, the brake system can restrict the machine running and keep the former knife position fixed.
 
3.4 Others
3.4.1 The light is equipped on the top of Slotting knife plate, easy for the night shift work.
3.4.2 Interlocking control switch assembled on the feeding, when abnormal printing or slotting can stop feeding
.
4 Driving gear
4.1 Main driven gear adopts *5 # steel material; Gears quenching, has excellent toughness and wear resistance.
4.2 Tooth surface gear shaving, improve the transmission stability.
5Joint Ring-Free technology
5.1 The Joint Ring- free technology adopted on the connection between the Big feeding gears, shaft sleeve head gear, planetary gear and shaft head, there will be no gap when doing the big torque, high positioning accuracy, overprint accurate.
5.2 It is more convenient to assembling and maintenance
 
6Others
6.1 This machine printing roll of rubber roller bearing adopts the TR bearing, other parts of the bearing. From domestic well-known brand products such as, Harbin, Wafangdian; Luoyang
6.2 Main motor adopts domestic high quality products.
6.3 Rubber roller adjusting motor adopts CPG,Taiwan.
6.4 Solenoid valve adopts JINQI ,Taiwan.
6.5 Slotting cutter adopts the QIFENG,Qingdao.
6.6 The whole machine control electrical parts from SCHNEIDER,France
6.7 PLC and the NT terminal display and the main electrical control components adoptFatak,Taiwan
6.8 Frequency converter adopt LG, South Korea.