Manual tablet press machine, beeswax foundaton press roller

Descripción del producto

Manual comb foundation mill

Manual Beeswax Comb Foundation Embossing Roller
Automatic Edge Cutting

Raw Material:Stainless Steel or or superhard aluminium alloy

*6cm X **5 mm ( length can be customer made according to customized requirement)

Weight:~*8kg

Size (L X W X H) **0 X **0 X **0 mm

 

MILLING WAX INTO USABLE FOUNDATION: Milling foundation by hand is not hard and is accomplished by placing warmed sheets of wax into a sleeve of plastic so that NO STRETCHING of the foundation takes place in any direction, DISTORTING THE CELL SIZE, while lowering the concentration of release agent used. (It also helps to break in a new machine not seasoned to constant milling.) Every time a sheet of wax is fed through the foundation mill, a water-bath with a 2% bio-degradable mild soap-suds must be used to keep the wax from sticking while also acting to keep the mill rollers seasoned (Note: wax contains minute amounts of acid which act on the metal rollers to make them stick). If sheets of wax fed through the foundation mills are not sleeved, GREAT CARE MUST BE TAKEN NOT TO STRETCH THE FOUNDATION THUS GIVING A DISTORTED CELL SIZE, as the wax is ejecting from the milling process. It is important to let the sheet of wax eject at normal turning speed without pulling on the sheet of wax to help it along. If wax should severely stick to the surface of the mills GREAT CARE MUST BE TAKEN NOT TO DAMAGE THE MILLING SURFACE OF THE ROLLERS, in removing it! The easiest way to remove stuck wax on rollers is to pour boiling water over them and gently brush with a plastic or animal bristle brush until gone. NEVER USE METAL TYPE BRUSHES NO MATTER HOW SOFT YOU THINK THEY ARE TO CLEAN WITH. After cleaning, then seasoning with clean release agent must start again on the stubborn spot.

Prior to milling, the sheets of wax need to be pre-heated to between *0 – **0 degrees F, uniformly throughout. To do this they can be either placed in a thermostat controlled water bath at constant temperature and soaked until warm, or merely placed into a thermostat controlled hot box and left to set until thoroughly warmed. (Note: If working with processed decontaminated wax, choose the warmed water-bath method, because one can not be too sure that full decontamination has been accomplished **0%. Around ***1, it was common practice to soak dipping boards in brine water for a few hours, the proportion of salt in the water being about a teacupful to about three pails of water. The salt served a double purpose: It acted somewhat as a lubricant in facilitating the removal of the sheets from the dipping boards, and as a preventive against the grain rising in the board and consequently, roughening. In the warmed water-bath method, back then also briny water of about **0 degrees F was used to soak and warm the sheets for milling.

Considering decontamination today, this might be an old practice worth following because an alkaline solution is used to hydrolyze coumaphos over time and briny water is alkaline! Thus after decontaminating in the Kelly wax press and photo degrading in UV rays of the sun, foundation making could continue the process by briny water bath by both dipping to sheet wax and soaking to warm prior to milling to make foundation.) While the sheets or stacks of wax are warming, the room you are milling in should be heated to a minimum of *0 degrees F (*0 degrees F being much better) to allow for rolling and embossing the foundation, without fighting the wax trying to cool too quickly, once removed from the either the warm water-bath or the hot-box it is being stored in, until milling actually takes place. Just prior to beginning milling, take boiling water and pour it over the mill rollers to pre-heat them up, so that you will not have warm sheets of wax meeting cold rollers to create a big milling mess. You can also pre-heat the rollers by placing a heating-pad around them for a few hours before hand. At any rate the rollers should be pre-heated to about *5 – **0 degrees F prior to beginning to roll wax sheets through the mill rollers.

During milling foundation, make sure the immediate milling area is clean of debris that could end up accidentally adhering to a warmed wax sheet and end-up fed into the foundation mill, only to damage the rolling/embossing surface permanently. Also make sure the gears of the mill (teeth on either end of the embossing rollers) are greased often with a heavy, thick, gear grease, to keep the gears running tight and lessening wear, that over the long haul can effect timing of the gears and the actual impression that is embossed. If you are working with a pre-set spaced foundation mill i.e. Tom’s Mighty Mini Foundation Embosser, plan on obtaining an average of 7 sheets of foundation to the pound for an average 8″ x *6 1/2″ embossed sheet of wax. If you are working with an adjusting foundation mill where you can change the thickness of the wax sheets you are embossing, be very careful not to screw down the mill rollers too much, thus damaging the embossing heads on the foundation rollers

(Note: If the foundation is feeding to one side and not rolling straight through the rollers, before you try to adjust the foundation mill to an adjustment that could make things worse, look at how you are dipping the wax sheets. The ripples or waves of the grain should run *0 degrees to the sides. If the ripples or waves run on the diagonal any way, even 5 – *0 percent, you are holding the dipping board wrong when you are dipping the wax sheets and creating the problem by careless dipping procedures). Stop here then and go back and redo your wax sheets until you learn to do it right! Properly made sheets of wax should feed true and list neither right, nor left, when being fed through the embossing rollers of the foundation mill.

Remember when milling foundation, with every sheet of wax fed, the rollers must be lightly soaped with biodegradable soap suds (that bubbly soap part!). To make an exception is to have the rollers stick wax and then need cleaning. To make plastic sleeves to put the wax sheet in prior to milling to avoid stretching the cells embossed, use plastic garbage baggies *0 x *6 in size, bought from your favorite Grocery Store. Each plastic garbage baggie will make three sleeves. Each sleeve will produce anywhere from ****0 embossed foundation sheets before needing to be changed, giving an average of *****0+ sheets embossed before having to use another new garbage baggie at an average cost of 5 cents each divided by 3. Following milling, stack embossed sheets of warm foundation neatly on another board or plate, by layering between sheets of pre-cut paper so that the wax sheets do not stick together. The neater the stacks, the better warmth will be retained within the stack of embossed sheets of wax. The longer the embossed sheets take to cool the greater the ductility of the foundation will be for handling later on when wiring into frames and taking to the field.