¿Aún no es miembro de TradeKey.com? Regístrese para conectarse con 9 millones de importadores y exportadores a nivel mundial.
registro |
BOOK A CALL
Book Call On Your Favorite Time

By Signing Up. I agree to TradeKey.com Terms of Use, Privacy Policy, IPR and receive emails related to our services

Contact Us
product
Prev
LED Decoration Light LED Decoration Light LED Decoration Light LED Decoration Light LED Decoration Light
Next

LED Decoration Light

100 ~ 1000 /

|

100 Piece Minimum Order

País:

China

N º de Modelo:

WJL-0021

Precio FOB:

100 ~ 1000 / Obtener el precio más reciente

Lugar de origen:

guangzhou

Precio de pedido mínimo:

100

Cantidad de pedido mínimo:

100 Piece

Detalle de embalaje:

carton package

El tiempo de entrega:

20 days

Capacidad de suministro:

1000 Piece per Month

Tipo de pago:

PayPal, L/C, T/T

Grupo de productos :

-

Contactar ahora
Miembro Básico

Persona de contacto Mr. Frank

32-4-302 LONGXIANG STREET,TIAN CAI MING YUAN 6-3-201, Jinhua, Zhejiang

Contactar ahora

Especificaciones del producto

  • led wheel cover light:led auto chassis lamps
  • car led emblem:led side vent light
  • solar antenna led light:EL car trim light

Descripción del producto

With special design ,it's very easy to install and use. It's low power consumption and also can make your car to get a charming fancy look. It's a latest amazing car accessory. Most importantly, as a DIY fun, your can install it at home which bring lots of convenience to you.

 
Introduction of function:
1.This product should be installed in the original position to replace the original logo(at the back of the car)
2.High quality water plating car badge, Laser and Reflective mirror
3.When the license plate lamp is turned on,the car logo light will be turn on too, which shines the logo in the night .
4.Special waterproof and dustproof design!
 
Installation:
1.First, spread a towel beside the car trunk (in order not to scratch the car body), with a flat head screwdriver, pry the car logo
 
2.Tear off the double-sided adhesive: pry it from the car body with moderate strength, steps by steps, slowly pry it down, then clean up the logo and car body .
 
3.Use crosshead screw-driver to uninstall the board inner the trunk, There are clips at somewhere, please carefully remove the insulation board ,you can see all kinds of lines.
 
4.Pass the power line of Car logo lamp through one of the logo location hole, pass inside the trunk and tear off the back of vehicle logo light
 
5.As the car logo lamp has installed, now connect the power supply.The logo lamp should connected with the light power supply of the rear license plate ,so that when turn on the small night lamp, the car logo lamp is also turned on Find the license plate lamp power connector
 
6.First pull the plug, and strip a opening separately of the positive and negative pole to show the wire core, Connect the lines(red to red and black to black) ,don't forget to wind then with insulating tape, Also, you need to plug back and set the insulation board to the trunk again!

País: China
N º de Modelo: WJL-0021
Precio FOB: 100 ~ 1000 / Obtener el precio más reciente
Lugar de origen: guangzhou
Precio de pedido mínimo: 100
Cantidad de pedido mínimo: 100 Piece
Detalle de embalaje: carton package
El tiempo de entrega: 20 days
Capacidad de suministro: 1000 Piece per Month
Tipo de pago: PayPal, L/C, T/T
Grupo de productos : -

Send a direct inquiry to this supplier

A:

Mr. Frank < ZHEJIANG LEDAUT AUTO PARTS & ELECTRONICS CO., LTD >

quiero saber: