Descripción del producto
1.Operation skills
a. Check the lubricating condition of the
bearing and the amount of the grease between the bearing and
bracket before the power is on
b. Check the state of all the fastener
carefully .
c. Check the condition of the rotating belt
.The broken belt should be changed at once and the greasy dirt
should be wiped out with clean rag ,if found on the belt or the
belt pulley .
d. Check if there is ore or other sundries in
the crushing cavity .If so, they should be eliminated
.
e. Materials can be feed once the machine
functions well .
f. The crushing materials should come into the
cavity evenly .Feeding side should be avoided preventing the sudden
load change or sudden increase on one side
G. Under the normal condition ,the temperature
of the bearing should not be over *5℃.The
machine should be stopped at once if it is over
*5℃ and we should find out the cause then eliminate
it .
H .Materials should be stopped feeding before
the power is off .And the machine can be shut off unless all the
materials are discharged out .
I. In crushing ,the electronic machine
should be shut off under this condition that the machine stopped
because of the materials jam in the crushing cavity .And Unless the
materials are eliminated the machine can be open
again.
2.FAQ
1).the metal hit-hit sounds are produced when the
machine is idling
a. The toothed plate of the jaw hits each other
.the solution is to adjust the discharging mouth.
b. The hit-hit sounds are produced during
the process of thrust plate bearing and shim adjusting .This is
made from the non flexible .damaged or loose spring .the solution
is to change the spring .
c. Because the moving jaw bracket is not
close to the machine body ,the hit-hit sounds are made between the
bracket and bearing or from the gasket adjusting. The solution is
to fix the gland nut .
2).The metal hit-hit sounds are
produced and the liner plate is vibrating when the machine is on
operation .This is because of the loose liner plate and toothed
plate in the crushing cavity ,the loose or the broken screw. The
solution is to fix or change in time .
3).The back bracket is broken frequently .This
is because that the spring is pressed too tightly so that it is
broken for the overloading crushing force .The solution is to
adjust the spring to the fit
4).The flywheel turns around and the machine
cannot work . This is because of the broken spring and pull rod
.And the bracket is falling down from the bearing slider because of
the dropping-out nut ,also the broken bracket .The solution is to
change and install .
5) The flywheel swings strongly and the
speed of the eccentric shaft is lower .This is because of the loose
or broken parts between the pulley and flywheel. Since the
wheel and axis cannot roll at the same time
6).The discharge granularity becomes thick
.This is because that the back parts of the crushing liner plate
are worn out strongly .The solution is to exchange the place of the
toothed plate or change a new one and adjust the discharging size
to the required one .
3.Care and Maintenance
a .Keep lubricate of the friction
surface to make sure the machine functions well and have a long
service life usage .
b. The grease should be selected based on
the place and temperature .Usually, the calcium ,nitro and sodium
soap grease .
c. The volumetric of the grease in
the bearing block should take up about *0% of the space volumetric
.And it should be changed one time **6 months .And be careful that
we must use the clean gas or paraffin to wash the rollaway nest of
the bearing .
d. Enough grease should be
poured into the gas between the toggle plate and its support before
the machine switches .
País: |
China |
N º de Modelo: |
oooo
|
Precio FOB: |
(Negociable)
Obtener el precio más reciente
|
Lugar de origen: |
Zhengzhou Henan Province |
Precio de pedido mínimo: |
- |
Cantidad de pedido mínimo: |
1 Set |
Detalle de embalaje: |
FOB |
El tiempo de entrega: |
within two months |
Capacidad de suministro: |
1000 Set per Year |
Tipo de pago: |
Other, PayPal, Western Union, D/P, L/C, T/T |
Grupo de productos : |
mining machinery
|