Electrical Discharge Sawing Machines

Detailed description

 

Benefits you will get with EDS machines: 

Benefit A. Saving  production time (Max cutting speed: ***0mm2/min)

Benefit B. Saving tool cost (the electrode is cheaper: around 1.2USD/pcs)

Benefit C. Saving material cost (the cutting gap is smaller: 1.**2mm)



I.The machine characteristics:

(1)The machine utilizing anodic machining principle, cutting special steel that cant be easily cut, such as high-temperature heat-resistant alloys, high chromium, high nickel alloy, titanium alloy. It can also cut steel rail.

(2)The cutting efficiency is high, the maximum cutting speed is ***0mm2/min

(3)Use steel as the electrode, the cost is rather lower

(4)Cutting gap, ≤2mm, save precious steel





 II. Specification



 




























































































 

Model No.	EDS**0	EDS**0	EDS***0
Max. cutting diameter	φ**0mm	φ**0 mm	φ***0 mm
Max. workpiece width	**0mm	***0mm	***0mm
Max. cutting travel	**0mm	**0mm	***0mm
Max. cutting length	Unlimited	Unlimited	**0mm
Worktable dimensions	**0x***0mm	***0x**0mm	***0x***0mm
Worktable moving travel	**0mm	**0mm	**0mm
Max cutting speed	***0mm2/min	***0mm2/min	***0mm2/min
Max. worktable load	***0kg	***0kg	****0kg
Electrode size	0.7～1.2(thickness)x****0(W)x***0(L)	0.7~1.2(thickness)x****0(W)x***0（L）	0.7~1.2(thickness)x****0(W)x***0（L）
Cutting gap	≤2mm	≤2mm	≤2mm
Electrode Material	Steel	steel	steel
Max. output current	**0A	**0A	***0A
Controller	German Siemens	German Siemens	German Siemens
Feeding motor	Japan Panasonic AC servo motor	Japan Panasonic AC servo motor	Japan Panasonic  AC servo motor

III. Introdution of Electrical Discharge Sawing machine.

1、Working theory

 The machine utilizing anodic machining principle, cutting special steel that cant be easily cut, such as high-temperature heat-resistant alloys, high chromium, high nickel alloy, titanium alloy. And the electrode is the mild steel, which is running fast on the pulleys.

 

The work piece is positioned on the worktable. And the mild steel electrode connects with the plus end of the power supply. And the work piece to the minus end of the electrical power supply. There is a flushing device which can supply sodium silicate solution (the coolant) to the cutting area. The electrical discharging happens continually between the mild steel and the work piece according to the drawing.

 

2、Simple description

The machine is equipped with the main machine body, working liquid system and controller.

1) The main machine body

The machine is gantry structure which is made up with the worktable parts, moving crossbeam and upright column the motorized electrode, etc.

â‘´ Worktable

The worktable is used for holding and adjusting the work piece. The worktable moves from point to point or continually, derived by the motor and couple and ball screw on the V guide way of the machine body.

 â‘µ Device of running the belt type steel electrode.

This device has functions of running& guiding and controlling the tension of the belt type electrode steel and also the function of higher power supply feeding, and checking and protection of belt-breaking.

The belt type steel electrode is running on the driving pulley and slave drive ones which are installed on the both holders of two ends of the crossbeam.

The driving pulley is moved by the 3 phases motor and the slave drive pulley by hydraulic pressure. The belt type steel electrode is guided with two guiders in order to make sure the electrode is under good tension condition. And the belt type steel electrode tension can be adjusted by the hydraulic pressure. In case the belt type electrode breaks or the tension is weak, the alarm will appear at once and the machine will stop working too. The power supply feeds through the pulley, installed with the power feed brush, pulley axle and to the belt type steel electrode.

The steel belt electrode is held by four sets of guiders in order to make the electrode running in the same surface of the work piece cross section and make the cutting gap as small as possible.  There are flushing mouths on the guiders, which offer the working liquid to the cutting area.

 â‘¶ Upright column and device of the motorized belt type steel electrode.
  The device of the motorized belt type steel electrode is moved by the A/C servo motor which drives the gear reducing mechanism with ball screw. So the belt type steel electrode can move to/away the work piece.
The upright columns are installed the linear guide ways, which hold the device of the motorized belt type steel electrode. In order to make the device move flexibly and reduce the loading of the servo motor, there are the weight balance parts connected with the device of the steel electrode by a roller chain inside of the upright columns.

The limited switches are installed on the device of the motorized electrode. And there is a traveling ruler near to the device for the operator to check the travel during working. 

2、The system of working liquid

The working liquid is taken to the flushing mouths by pump. And then it flushes to the work piece by the adjustable mouths and return to the collecting tank. The liquid after filter can be used repeatedly. 

 

The supplier will supply the way how to mix the working liquid and the installation floor plan. And the end user designs and builds the liquid tank and the collecting liquid path according to the floor plan and also the workshop area.

3、Electrical power supply and control

 â‘´machining electrical power supply

The machine applies the special linear transform to exchange the 3 phases A/C electrical power into the lower voltage and high current working power supply.

Main specification of the power supply:

Input：3 Phases **0V *0Hz

Output：*2V～*0V divided into adjustable 4 levels. 

Max machining current：**0A/**0A/***0A subject to different models.

ʉԵController system

The machine applies the programmable PLC to control the running of all kinds of functions stable.
  The power units are 3 phases asynchronous motors expect the Panasonic A/C motor that drives the device of the belt type steel electrode. All motors return circuits are installed with the protecting switches to avoid the overloading.
The system of the auto feeding steel electrode can inspect the discharging gap in real time, and it will adjust the feeding speed automatically according to the working situation in order to make the cutting under the stable and efficient condition.