Descripción del producto

DH556
Introduction
1. overview
DH556 is the new generation high performance fully digital stepper drive which base on 32bit DSP with a advanced algorithm .the power supply range is DC20~50V. it can drive frame 42---86mm 2 phase stepper motor .
Ultra low noise and high smoothness at middle/low speed ,and high torque at high speed, which can be applied to different speed control applications. adopt smooth and accurate sinusoidal current vector control technology ,which make motor low heat .
2. features
●new generation 32bit DSP
●good smoothness ,low noise ,low heat
●build-in micro step setting
●build-in current setting
●the standstill current can be set to 50%
●opto-isolated differential pulse
●the response frequency is up to 300KHz
●over voltage , under voltage, over current protection
3. applications
It can be used in various kinds of machines ,such as dispenser machine. floating machine
3D printer, labelling machine, medical machine, laser cut machine, and so on ,its unique features make it an ideal solution for the applications which require low noise ,low vibration, low heat and high precision
Mounting dimension（unit：mm）



Function
1:Current setting

Peak current(A)	RMS current  (A)	SW1	SW2	SW3
1.4	1.0	OFF	OFF	OFF
2.1	1.5	ON	OFF	OFF
2.7	1.9	OFF	ON	OFF
3.2	2.3	ON	ON	OFF
3.8	2.7	OFF	OFF	ON
4.3	3.1	ON	OFF	ON
4.9	3.5	OFF	ON	ON
5.6	4.0	ON	ON	ON

2:Standstill current setting
SW4：OFF=Half Current
ON=Full Current
3:Micro step setting

Pul/rev	SW5	SW6	SW7	SW8
200	ON	ON	ON	ON
400	OFF	ON	ON	ON
800	ON	OFF	ON	ON
1600	OFF	OFF	ON	ON
3200	ON	ON	OFF	ON
6400	OFF	ON	OFF	ON
12800	ON	OFF	OFF	ON
25600	OFF	OFF	OFF	ON
1000	ON	ON	ON	OFF
2000	OFF	ON	ON	OFF
4000	ON	OFF	ON	OFF
5000	OFF	OFF	ON	OFF
8000	ON	ON	OFF	OFF
10000	OFF	ON	OFF	OFF
20000	ON	OFF	OFF	OFF
25000	OFF	OFF	OFF	OFF

4、Interface description

Name	function	description
PWR	Power light	When power on ,the green light is on
ALARM	Over current/under voltage/over voltage displaying light	If the drive Over current/under voltage/over voltage, the red light is on
PU+	Pulse positive	Pulse signal: In single pulse (pulse/direction) mode, this represents pulse signal, each falling edge active; 4-5V for High -level, 0-0.5V for low-level Series connect resistors for current-limiting when +12V or +24V used.(should connect 1k resistor for +12V,2k for +24V)
PU-	Pulse negative	Pulse signal: In single pulse (pulse/direction) mode, this represents pulse signal, each falling edge active; 4-5V for High -level, 0-0.5V for low-level
DR+	Direction  positive	DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; Series connect resistors for current-limiting when +12V or +24V used.(should connect 1k resistor for +12V,2k for +24V)
DR-	Direction  negative	DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation;
MF+	Enable positive	Enable signal: This signal is used for enabling/disabling driver. High level for enabling the driver and low level for disabling the driver. Usually leftUNCONNECTED (ENABLED). Series connect resistors for current-limiting when +12V or +24V used.(should connect 1k resistor for +12V,2k for +24V)
MF-	Enable negative	Enable signal: This signal is used for enabling/disabling driver. High level for enabling the driver and low level for disabling the driver. Usually leftUNCONNECTED (ENABLED).
V-	Power COM	DC20-50V
V+	Power VCC
A+,A-	Motor A phase	Connect to   Motor A phase
B+,B-	Motor B phase	Connect to   Motor B phase

！Note
1: Connect power supply rightly ,cant exceed 50VDC
2: If the control signal (PU, DR, MF ) is over 5V ,please connect resistors (at the PU+, DR+, MF+ terminals) for current-limiting.
3:if the alarm light is on ,please check it after power off
A :the power supply range is 20V—50VDC or not ? B:is there any short on motor wire or others ?

 

País:	China
N º de Modelo:	-
Precio FOB:	( Negotiable ) (Negociable) Obtener el precio más reciente
Lugar de origen:	-
Precio de pedido mínimo:	-
Cantidad de pedido mínimo:	1 Piece
Detalle de embalaje:	carton
El tiempo de entrega:	20days
Capacidad de suministro:	500 Piece per Month
Tipo de pago:	T/T, Western Union
Grupo de productos :	stepper drive