addition cure liquid silicone rubber raw material for mold making

Precio FOB

Obtener el precio más reciente

7.5 ~ 12 USD / Kilogram ( Negotiable )

100 Kilogram Minimum Order

País:

China

N º de Modelo:

G-830 addition cure silicone rubber

Precio FOB:

7.5 ~ 12 USD / Kilogram ( Negotiable )(Negociable) Obtener el precio más reciente

Lugar de origen:

China

Precio de pedido mínimo:

7.5 per Kilogram

Cantidad de pedido mínimo:

100 Kilogram

Detalle de embalaje:

20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing f

El tiempo de entrega:

3 to 5 days

Capacidad de suministro:

500 Ton per Month

Tipo de pago:

Other, PayPal, Western Union, L/C, T/T

Grupo de productos :

addition cure silicone rubber

Contactar ahora

Dongguan Guochuang Organic Silicone Material Co., Ltd.

China

Miembro Básico

Persona de contacto Ms. Sybil

NO.4 shichang street , the 2nd industrial district of xiaobian ,changan town ,dongguan China., Dongguan, Guangdong

Contactar ahora

Descripción del producto

1.Description of addition cure liquid silicone rubber
G***0 silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fastly by heating, Its two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible.

2.Characteristics of addition cure liquid silicone rubber
(1).An exceptional fluidity and good operability
(2).Good tensile strength and tear strength
(3).Food grade silicone rubber
(4).high temperature resistance
(5).good flexibility
(6).No smell ,non-toxic
(7).long shelf-time &lifetime
(8).Lower shrinkage

3.Application of addition cure liquid silicone rubber
G***0 silicone rubber is flexbile silicone rubber ,it has a higher temprature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing .4.Datesheet of addition cure liquid silicone rubber

Item No.	Appearance	Hardness (shore A°)	Viscosity (CPS)	Tensile-strength ( kgf /cm2 )	Tear-strength (kgf /cm2 )	Elongation-break (%)	Mixing ratio	operation *time (5â„ƒ** )	*Curing time( 5 â„ƒ**)	Shrinkage
G0*	translucent	*0±2	*0±*0	≥*5	≥*4	≥**0	1:1	****0 mins	2~3 h	≤0.1%

Using instruction
1. Place a plastic container on a small scale, making sure to zero out the weight on the scale. Note: use a container that, during rise under vacuum in Step 5, will allow for material to expand to **5 times its resting volume.

2. Pour catalyst into the plastic container, noting weight of material poured.
3. In the same container, pour an equal weight of base on top of the catalyst (e.g., **0 grams of catalyst and **0 grams base). Note: within a 5% weight variance, the end result is not altered.
4. With a clean, dry mixing spatula, mix energetically until the color of the product is homogeneous. Note: working time begins at this step. Mixing should take no longer than **2 minutes.
5. Place container under vacuum and vacuum until material bubbles and rises. Release vacuum and repeat until bubbles are removed. Vacuuming should take no longer than **4 minutes.
6. From a height of approximately *0 cm, pour the mixed silicone into the mold frame. Maintain the pouring stream in the same spot so as to minimize introduction of air bubbles into the mold.
7. Allow the mold to sit, undisturbed, for at least 4 hours to ensure the silicone is fully cured.
8. Remove the mold from the frame.
9. Cut around the pattern carefully to release it from the silicone rubber mold.
Notice
The surfaces with which the material comes in contact must be perfectly clean, free of grease and dry.
Close the bottles after use so as not to confuse the cap of the catalyst with that of the base when re-sealing.
Be aware of possible cross-contamination; its highly recommended to use only dedicated gear when processing poly-addition RTV2 silicone rubber (including degassing devices).
Be aware that contact with certain material can inhibit the curing of the RTV2 poly-addition silicone rubber. Common contaminants to be avoided include:
-Natural or synthetic rubber, vulcanized with sulphur derivatives.
-Poly-condensation RTV catalyzed with metallic salts.
-PVC stabilizing agents.
-Amine cured epoxies.
-Sulphur, tin and amines derivatives.
-In case of doubt, carry out a small test by pouring the mixture onto a small area of the object.

Packaging & Shipping
Packing:
*0KG/drum vacuum packing for part A + *0KG/drum vacuum packing for part B
*5KG/drum vacuum packing for part A + *5KG/drum vacuum packing for part B
**0KG/drum packing for part A ***0KG/drum packing for part B
Why Choose Us?
1.Free Sample
2.Sample Test
3.Technical Support
4.Engineers Site Instruction
5.New products developing
6.New Market developing
7.Factory Visiting Reception
8.China visiting reception
9.China Latest silicone news
*0.Related Products Purchasing Assistance
*1.More than 8 years experience in producing liquid silicone rubber

País:	China
N º de Modelo:	G-830 addition cure silicone rubber
Precio FOB:	7.5 ~ 12 / Kilogram ( Negotiable ) (Negociable) Obtener el precio más reciente
Lugar de origen:	China
Precio de pedido mínimo:	7.5 per Kilogram
Cantidad de pedido mínimo:	100 Kilogram
Detalle de embalaje:	20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing f
El tiempo de entrega:	3 to 5 days
Capacidad de suministro:	500 Ton per Month
Tipo de pago:	Other, PayPal, Western Union, L/C, T/T
Grupo de productos :	addition cure silicone rubber